Grizzly Coffee Grinder T10023 User Manual

MODEL T10023  
ACCESSORY KIT #1  
FOR T10010/T10097  
WET GRINDER  
INSTRUCTION SHEET  
Introduction  
Inventory (Figure 2)  
the model t10023 accessory Kit #1 for the model  
t10010/t10097 Wet grinder includes fixtures for  
sharpening small knives, large knives, scissors  
and axes.  
A. scissors sharpening Jig............................. 1  
b. axe sharpening Jig.................................... 1  
C. scissors Clamp .......................................... 1  
D. large Knife sharpening Jig........................ 1  
E. scissors sharpening Jig Knobs ................. 2  
F. Knife sharpening Jig Knobs....................... 2  
G. small Knife sharpening Jig........................ 1  
b
a
C
d
g
e
Figure 1. t10023 accessory Kit  
f
Unpacking  
Figure 2. inventory.  
the model t10023 accessory Kit was carefully  
packed when it left our warehouse. if you discover  
any parts are damaged after you have signed  
for delivery, please immediately call Customer  
Service at (570) 546-9663 for advice. save the  
containers and all packing materials for possible  
inspection by the carrier or its agent. Otherwise,  
filing a freight claim can be difficult. When you  
are completely satisfied with the condition of your  
shipment, you should inventory the contents.  
Adhere to all safety warnings outlined in  
the Model T10010/T10097 Wet Grinder user  
manual. If you are not familiar with the prop-  
er usage of the Model T10010/T10097 Wet  
Grinder, review the procedures and safety  
warnings covered in that manual. Failure to  
do so could result in damage to the machine  
or personal injury.  
Copyright © November, 2007 by grizzly iNdustrial, iNC. revised marCh, 2011 (Jb)  
WARNING: NO pORTION OF THIS MANUAL MAY bE REpRODUCED IN ANY SHApE  
OR FORM WITHOUT THE WRITTEN AppROvAL OF GRIzzLY INDUSTRIAL, INC.  
(for models maNufaCtured siNCe 11/07) #Jb10086 priNted iN ChiNa  
 
5. tighten the lock knob to clamp the knife into  
the jig.  
Using the Knife Sharpening Jigs  
for blades shorter than 4", use the small knife  
sharpening jig. for blades longer than 4", use the  
large sharpening jig.  
6. adjust the position of the universal support to  
achieve the approximate grinding/stropping  
angle.  
1. uNplug the griNder from poWer!  
7. adjust the position of the locking ring to fine  
tune the grinding/stropping angle (Figure 8).  
2. place the universal support in the horizontal  
mounts on the grinder so that the grinding will  
occur with the rotation direction.  
Knife  
3. loosen the clamping knob enough to allow  
the knife to slide in and loosen the lock knob  
far enough so that it does not extend through  
the clamp plate (Figure 6).  
lock Knob  
universal support  
locking ring  
Figure 8. Knife sharpening.  
8. tighten all knobs before reconnecting the  
grinder to power to perform the operation.  
Clamp plate  
Clamping Knob  
Tips for using the knife sharpening jigs:  
Figure 6. Knob identification.  
reposition the universal support for coarse  
angle adjustments.  
4. insert a knife into the clamp as shown in  
Figure 7 and tighten the clamping knob.  
reposition the lock ring on the knife sharpen-  
ing jig for fine angle adjustments.  
Clamping Knob  
lock Knob  
always grind with the direction of rotation of  
the grinding/stropping wheels  
always use a smooth, stroking motion with  
even pressure, keeping the blade flat against  
the wheel for optimal results.  
pivot the knife sharpening jig on the universal  
support as needed to follow the contour of the  
knife blade.  
Figure 7. Knife clamping.  
-3-  
t10023 Wet grinder accessory Kit #1  
 
Using the Scissors Sharpening Jig  
1. uNplug the griNder from poWer!  
lock Knob  
2. place the universal support in the vertical  
mounts on the grinder, and adjust the univer-  
sal support approximately 1" away from the  
grinding wheel.  
3. slide the scissors sharpening jig onto the  
universal support, as shown in Figure 9, and  
tighten the knobs.  
Clamping Knob  
Figure 11. scissors clamping.  
6. tighten the lock knob to securely clamp the  
scissors into the scissors clamp.  
7. place the scissors clamp on the rails of the  
sharpening jig. adjust the height of the uni-  
versal support or the angle of the sharpening  
jig as needed so that the clamp sits flat on  
both rails as shown in Figure 12.  
Rails  
Beveled  
Edge  
Figure 9. scissors sharpening jig position.  
Sharpening  
Jig  
4. loosen the clamping knob enough to allow  
one blade of the scissor to slide in, and loos-  
en the lock knob far enough so that it does  
not extend through the upper portion of the  
clamp (Figure 10).  
Scissor  
Blade  
Grinding Wheel  
Figure 12. scissors clamp placement.  
Clamping Knob  
lock Knob  
8. fine tune the position of the universal jig and  
the angle of the scissors jig until the beveled  
edge of the blade sits flat against the grinding  
wheel, as shown in Figure 12.  
9. tighten all knobs and reconnect the grinder  
to power before grinding.  
Tips for using the scissors sharpening jig:  
Clamp plate  
always use a smooth stroking motion with  
even pressure, keeping the blade flat against  
the wheel for optimal results.  
Figure 10. scissors clamp knobs.  
5. insert one blade of the scissors into the  
clamp, as shown in Figure 11, and tighten  
the clamping knob.  
do not use the stropping wheel with the uni-  
versal support in the vertical mounts.  
-4-  
t10023 Wet grinder accessory Kit #1  
 
T10023 parts breakdown and List  
3
4
15  
1
1
2
14  
5
13  
12  
6
7
11  
8
13  
3
4
1
1
2
5
9
11  
10  
16  
17  
1
1
8
1
17  
18  
1
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
PT10023001  
PT10023002  
PT10023003  
PT10023004  
PW03M  
KNURLED SCREW M6-1 x 16  
STOP RING  
10  
11  
12  
13  
14  
15  
16  
17  
18  
PT10023010  
PT10023011  
PT10023012  
PT10023013  
PTLW13M  
LARGE KNIFE SUPPORT  
SCISSOR JIG RAIL  
STOP RING KNOB  
SCISSOR JIG HOLDER  
SCISSOR JIG KNOB  
HANDLE  
FLAT WASHER 6MM  
SMALL CLAMP PLATE  
SMALL KNIFE SUPPORT  
COMPRESSION SPRING  
LARGE CLAMP PLATE  
INT TOOTH WASHER 6MM  
CAP SCREW M6-1 X 12  
SCISSOR SUPPORT  
PT10023006  
PT10023007  
PT10023008  
PT10023009  
PSB26M  
PT10023016  
PT10023017  
PT10023018  
SCISSOR CLAMP PLATE  
AXE SHARPENING JIG  
 
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!  
~Since 1983~  
Visit Our Website Today For  
Current Specials!  
ORDER  
24 HOURS A DAY!  
1-800-523-4777  
 

Harbor Freight Tools Outdoor Storage 91121 User Manual
Hearth and Home Technologies Stove SANTAFEI B User Manual
HP Hewlett Packard Computer Drive LP 1000r User Manual
HP Hewlett Packard Server DL365 User Manual
HP Hewlett Packard Switch HN220E User Manual
HTC Cell Phone S740 User Manual
Hunter Fan Air Cleaner 30835 User Manual
Hunter Fan Outdoor Ceiling Fan 42426 01 User Manual
Hypertec Carrying Case N13268PHY User Manual
IBM Laptop 67P4573 User Manual