HANNspree Flat Panel Television HANNSrobby User Manual

9.6" Liquid Crystal Display  
12.1"  
Television  
User's Manual  
MAK-000003  
 
Table of Contents  
1
 
Table of Contents  
2
 
1
Regulatory Information  
FCC Compliance Statement1  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
Additional Information  
This equipment has been tested and found to comply with the limits for  
a Class B digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses  
and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to  
radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment and receiver  
Connect the equipment into an outlet on a circuit different from that  
to which the receiver is connected  
Consult the dealer or an experienced radio/TV technician for help  
Warning: You are cautioned that changes or modifications not  
expressly approved by the party responsible for compliance could void  
your authority to operate the equipment.  
1. applies only to products purchased in the United States of America  
3
 
 
DOC Compliance Notice1  
This digital apparatus does not exceed the Class B limits for radio noise  
emissions from digital apparatus as set out in the Radio Interference  
Regulations of the Canadian Department of Communications.This  
device complies with Canada ICES-003 Class B.  
CE Conformity Statement2  
This device complies with the requirements set out in the Council  
Directive on the approximation of the Laws of the Member States  
relating to Electromagnetic Compatibility (89/336/EEC) and the  
Amendment Directive (92/31/EEC), Low-Voltage Directive (73/23/EEC)  
and the Amendment Directive (93/68/EEC).  
1. applies only to products purchased in Canada  
2. applies only to products purchased in the European Union  
4
 
2
Description of Warning Symbols  
Before You Proceed  
1. Read all Safety Notices in Section 2 of this manual and  
instructions in the User’s Manual carefully before either plugging  
in or turning the TV on.  
2. Keep this User’s Manual in a safe place for future reference.  
Keep the box and packaging in case the TV needs to be shipped  
in the future.  
3. Follow the TV and warning label instructions.  
4. Any uses, operations, changes, alterations or modifications of  
the TV that do not follow the instructions in this manual will void  
this TV’s warranty.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
WARNING  
CAUTION  
This symbol is used to alert  
users to pay attention to  
important descriptions  
regarding usage, maintenance  
(repair), and additional  
important information related  
to this TV.  
This symbol is used to alert  
users to the risk of electric  
shocks due to dangerous and  
uninsulated components.  
5
 
 
3
Safety Notices  
Electric Power Notice  
Electric power may cause personal injury and mechanical damage if  
misused. Although safety has been taken into consideration during the  
design and production of this TV, electric shock or fire can result if the  
TV is misused. To prevent potential danger, read and follow the  
instructions and warnings contained in this manual when setting up,  
operating or cleaning the TV. In addition, please read all “Safety  
Notices” contained in this manual carefully before using the TV.  
Power Supply Safety Notes  
1. To avoid electric shocks, do not use an extended power cord or  
an outlet that does not match this TV's plug or leaves the plug  
exposed.  
2. This TV has a 3-pin grounded plug. The third pin connects to  
ground; do not remove it or alter it in anyway.  
3. If the power cord or plug is damaged or worn, unplug it  
immediately and contact an authorized service technician for  
maintenance.  
4. To avoid fire or electric shocks, do not overload electric power  
outlets.  
6
 
 
Installation Safety Notes  
Antenna  
We suggest that you use an outdoor antenna to get the best signal  
possible unless you have cable TV or a centralized indoor antenna  
system. You may, however, use an antenna indoors if it is placed in a  
location free from interference.  
Location  
Avoid prolonged exposure to sunlight or other strong sources of heat.  
Leave sufficient distance between the TV and the wall to provide  
enough space for the emission of heat.  
WARNING  
To reduce the risk of fire or electric shock, do not expose this  
apparatus to rain or moisture.  
Apparatus shall not be exposed to dripping or splashing and no  
objects filled with liquids, such as vases, shall be placed on the  
apparatus.  
Power  
To avoid danger of fires or electric shock, only use those adapters  
listed below, which are compatible with this TV.  
EDAC POWER ELECTRONICS CO., LTD.: EA1050E-120  
LI SHIN INTERNATIONAL ENTERPRISE CORP.: 0217B1240  
7
 
IMPORTANT SAFETY INSTRUCTIONS  
1
2
3
4
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
5
6
7
8
9
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings. Install  
in accordance with manufacturer’s  
instructions.  
Do not install near any heat sources such as  
radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce  
heat.  
Do not defeat the safety purpose of the  
polarized or grounding-type plug. A polarized  
plug has two blades with one wider than the  
other. A grounding-type plug has two blades  
and a third grounding prong. The wide blade  
or the third prong are provided for your  
safety. If the provided plug does not fit into  
your outlet, consult an electrician for  
replacement of the obsolete outlet.  
8
 
10 Protect the power cord from being walked on  
or pinched, particularly at plugs,  
convenience receptacles, and the point  
where they exit from the apparatus.  
11 Only use attachments/accessories specified  
by the manufacturer.  
12 Use only with the cart, stand, tripod, bracket,  
or table specified by the manufacturer, or  
sold with the apparatus. When a cart is used,  
use caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
13 Unplug this apparatus during lightning  
storms or when unused for long periods of  
time.  
14 Refer all servicing to qualified service  
personnel. Servicing is required when the  
apparatus has been damaged in any way,  
such as power-supply cord or plug is  
damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus  
has been exposed to rain or moisture, does  
not operate normally, or has been dropped.  
These servicing instructions are for use by  
qualified service personnel only.To reduce  
the risk of electric shock, do not perform any  
servicing other than that contained in the  
operating instructions unless you are  
qualified to do so.  
CAUTION  
9
 
Personal Safety  
To avoid overloading the power supply, never  
plug too many electrical devices into an outlet,  
power strip, or extension cable.  
Dangerous high-voltage electric power  
components are located inside the TV. To avoid  
electric shock, do not disassemble the TV in any  
way.  
Do not place or drop metals, small objects, or  
flammable materials into the vent of the TV.  
If the TV is dropped, falls down, or is otherwise  
damaged, unplug the power cord immediately  
and contact an authorized service technician.  
If any fluid is sprayed or dropped into the TV,  
contact an authorized service technician.  
The screen of the TV is made of glass. Avoid  
hitting or scraping it. If the screen is broken, do  
not touch the broken glass.  
Do not allow children to use the TV unattended.  
10  
 
Installation  
Do not place the TV in locations where there is  
excessive steam or dust.  
Avoid blocking the TV's vents, do not place the  
TV on a bed, sofa, carpet, or in a sealed cabinet.  
Install the outdoor antenna (not included) away  
from power transmission lines to avoid possible  
danger.  
Unplug the power cord and antenna connector  
when there is a storm or when the TV is not in  
use for long periods to avoid electric shock from  
lightning.  
11  
 
Operation  
This TV is designed for home power sources as  
labeled on the casing. Avoid using any other  
power accessories to avoid electric shock or  
other damage.  
V
The plug can be inserted into an outlet in only  
one direction as shown to the left. Do not alter  
the plug. Contact an authorized service  
technician if you cannot plug it in correctly.  
If there is any problem that cannot be resolved  
according to the instructions given in this  
manual, contact an authorized service technician  
immediately. Do not attempt any methods not  
covered in this manual.  
Maintenance  
Do not attempt to repair the TV by yourself.  
Contact an authorized service technician. Ask  
the service technician to complete a safety  
inspection before switching the power on after  
completing any maintenance.  
12  
 
4
Preface  
Thank you for purchasing a Hannspree Liquid Crystal Display Television  
(LCD TV). Your new TV will allow you to enjoy superior audio and video  
while enriching your lifestyle with advanced technology.  
Please carefully read this manual in its entirety before setting up, using  
or operating your TV. To ensure the safe and correct installation and  
operations of the TV, it is important that the safety and operation  
instructions in this manual are followed.  
This instruction manual is designed to assist you in setting up and using  
the TV. The information in this manual has been carefully checked for  
accuracy; however, no guarantee is given to the correctness of the  
contents. The information in this manual is subject to change without  
notice.  
To the extent allowed by applicable law, Hannspree California Inc.  
(“Hannspree”) shall not be liable for direct, indirect, special, exemplary,  
incidental or consequential damages arising from any defect or  
omission in this manual, even if advised of the possibility of such  
damages in advance.  
13  
 
 
Copyright  
© Copyright 2004 Hannspree California Inc.  
All rights reserved. This manual is protected by copyright and  
distributed under licenses restricting its use, copying and distribution.  
No part of this manual may be reproduced in any form by any means  
without the prior written authorization of Hannspree. The TV described  
in this manual may include copyrighted software of Hannspree (or other  
third parties). Hannspree (or other third parties) preserves the exclusive  
rights for copyrighted software, such as the right to distribute or  
reproduce the copyrighted software. Accordingly, and to the extent  
allowed by applicable law, any copyrighted software contained in the  
product described herein shall not be distributed, modified, reverse  
engineered, or reproduced in any manner without the prior written  
authorization of Hannspree (or of other third parties).  
The Hannspree logos presented herein are trademarks of Hannspree.  
All other product names, trademarks or logos mentioned herein are  
used for identification purpose only, and may be the trademarks or  
registered trademarks of their respective owners.  
The purchase of the product described herein shall not be deemed to  
grant, either directly or by implication, estoppel or otherwise, any  
license under the copyrights, patents, patent applications or trademarks  
of Hannspree, except for the normal, non-exclusive use that arises by  
operation of law in the sale of a product.  
14  
 
5
Introducing the TV  
Thank you for purchasing this LCD TV. Your LCD TV is designed to be safe,  
versatile, and easy to use. The design makes it a fun addition to any room.  
You can watch broadcast or cable television channels, and easily connect a  
VCR, VCD, DVD player or a game device to the standard RCA and S-Video  
input jacks that are included in the 4-IN-1 A/V cable.  
Convenient control buttons located on the TV and a handy remote control let  
you change channels, adjust the volume, and change display settings  
through an easy-to-use on-screen display menu system. The built-in stereo  
speakers provide full rich sound and a convenient audio output port lets you  
connect to an external audio system or headphones.  
Features  
Built-in TV tuner  
4-IN-1 A/V cable  
On-Screen Display (OSD) menu system  
Built-in stereo speakers  
15  
 
   
6
Checking Package Contents  
Make sure the following components are included in the box. Please contact  
Hannspree Customer Service immediately if anything is missing or  
damaged.  
TV  
User’s manual  
Quick start guide  
Warranty and service manual  
Power cord  
Power adapter  
4-IN-1 A/V cable  
Remote control and battery/batteries  
RCA jack x 3  
Stop Card  
16  
 
 
7
Getting Started  
Control Panel  
Description  
Icon  
Function  
Turns the TV on and off.  
/POWER  
Power  
Indicates power status.  
Power LED  
Selects the input source to be  
displayed  
(TV/CATV, AV or S-Video).  
SOURCE  
MENU  
Source  
Menu  
Turns the On-Screen Display (OSD)  
menu on and off.  
Changes channels. Press channel up  
to increase the channel number.  
Press channel down to decrease the  
channel number.  
channel up  
(X/ + / S)  
Select  
channel  
channel down  
(W / – / T)  
Press volume up to increase the  
audio volume. Press volume down to  
decrease the audio volume.  
volume up ( + )  
volume down ( – )  
Adjust  
volume  
17  
 
   
Input and Output Jacks  
Description  
Connector  
Function  
Use the included 4-IN-1 A/V  
cable to connect external  
devices, such as a VCR, VCD,  
DVD player, CVBS RCA  
cables or a game device.  
Audio Input: AV connector  
audio (white and red) cables.  
Video Input: AV connector  
video (yellow) or S-Video  
cable.  
4-IN-1  
(AV, AV IN)  
Connects to an antenna or  
CATV cable television line.  
ANT  
Connects to the included  
power adapter.  
DC-IN (DC-12V)  
Connects to headphones or  
external speakers  
Headphone /  
Speakers jack  
18  
 
 
Remote Control  
Description  
Icon  
Function  
Press this button to activate the OSD  
menu system and to adjust various  
settings and personal preferences.  
MENU  
Menu  
Arrow  
MENU  
/
/
ENTER  
PressS / T / W and X to scroll  
through the on-screen display  
menus.  
Favorite channels can be selected  
using the W and X buttons on the  
remote control.  
S / T / W / X /  
< / >  
1
4
2
5
3
6
Use to select a channel directly.  
Press 0-9 to enter the channel  
number (press 1 and 0 for channel  
10).  
Number  
Recall/Last  
MTS  
7
8
0
9
Press this button to return to the last  
channel selected.  
RECALL / LAST  
MTS  
Press this button to enable the  
bilingual function when the program  
has stereo/SAP/MONO capabilities.  
This option may not be available in  
your local area.  
Power  
Turns the TV power on or off.  
-VOL VOL+  
>VOL VOL<  
VOL VOL  
VOL VOL  
VOL VOL  
Press volume up to increase the  
audio volume. Press volume down to  
decrease the audio volume.  
Adjust volume  
19  
 
 
Description  
Icon  
Function  
Press this button to eliminate sound.  
Press mute again or press the  
volume adjust buttons to restore  
sound.  
MUTE  
Mute  
Changes channels. Press channel  
up to increase the channel number.  
Press channel down to decrease the  
channel number. In AV mode, press  
either button to return to TV mode.  
CH CH  
CH CH  
CH CH+  
Select channel  
Source  
Press this button to cycle the video  
input sources. The source is  
displayed on the screen.  
SOURCE  
AUTO  
Press this button to automatically  
adjust the screen parameters in PC  
mode. Only available with 15-inch  
TVs.  
Auto (selected  
models only)  
Press this button to show messages  
on the screen, such as the channel  
number. Press this button again to  
close the displayed message.  
Display (selected  
models only)  
DISPLAY  
RESET  
Reset (selected  
models only)  
Press this button to reset the TV.  
20  
 
Inserting the Remote Control Battery/Batteries  
Lithium battery/batteries  
1
Open the battery compartment cover at the  
back of the remote control (A).  
A
2 Slide the battery/batteries, with the positive  
(+) side facing up, underneath the shorter set  
of metal contacts (B).  
B
3 Press the battery/batteries firmly into place  
C
D
in the battery compartment (C)  
4 Replace the battery compartment cover (D).  
Note  
Your remote control may have either AAA type batteries or CR2032 lithium  
battery/batteries.  
21  
 
 
AAA battery/batteries  
1
Open the battery compartment cover at the  
back of the remote control (A).  
A
B
C
2 Insert the battery/ batteries paying  
attention to the polarity markings inside  
the battery compartment (B).  
3 Replace the battery compartment cover  
(C).  
Note  
Your remote control may have either AAA type batteries or CR2032 lithium  
battery/batteries.  
22  
 
CAUTION  
If the remote control is not used for a long period, remove the batteries  
and store them separately.  
Handle damaged or leaking batteries carefully, and wash hands after  
such handling.  
If your remote control has two batteries, do not mix new and old  
batteries because the life of the new batteries will be shortened.  
Chemical fluids may leak from the old batteries.  
Danger of explosion if battery is incorrectly replaced. Replace only with  
the same or equivalent type recommended by the equipment  
manufacturer. Discard used batteries according to manufacturer’s  
instructions.  
Refer to your local recycling or waste disposal rules and contact a local  
waste disposal vendor to dispose of used batteries.  
The remote control may have a magnet in it, so do not place magnetic  
sensitive items such as watches, credit cards, or flash media close to  
the cover.  
Do not use force when pulling the remote control cover open; you may  
damage the hinge.  
23  
 
8
Making Connections  
Connecting to an Antenna or Cable TV  
1
Connect one end of the VHF/UHF (Antenna) or CATV cable to ANT  
Jack (VHF/UHF IN Jack) on the back of the TV.  
2 Connect the other end of the VHF/UHF (Antenna) or CATV cable to  
the antenna socket or CATV cable.  
Antenna  
ANT  
ANT jack  
(VHF/UHF IN jack)  
Antenna/CATV  
socket  
Antenna/CATV  
coaxial cable  
Note  
If you cannot receive channels after connecting to an antenna or cable TV  
line, try scanning for channels. See “Auto Program” on page 47.  
24  
 
   
Connecting to AV Devices  
Connect external devices such as a VCR, VCD, DVD player, or video game  
console to the TV using the supplied 4-IN-1 A/V cable.  
Connecting to a VCR/VCD/DVD Player  
The illustration presented here shows how to connect the TV to a VCR,  
VCD or DVD player. Actual connections may vary according to the make  
and model of the device. Refer to the user’s manual included with the device  
for more detailed instructions.  
VCR  
DVD  
VCD  
4-IN-1  
4-IN-1 A/V jack  
B
R W Y  
S-Video  
connector  
AV  
connectors  
4-IN-1 A/V cable  
Note  
The cables are color-coded (black, red, white, yellow). Connect each  
color-coded cable to the appropriate connector on your device.  
When connecting the S-Video connector and AV connector at the same  
time, the priority is given to the S-Video connector.  
25  
 
   
Connecting to a Video Camera  
The instructions presented here are a general guide to connecting the TV to  
a camcorder or other type of digital camera. Actual connections may vary  
according to the make and model of the device. Refer to the user’s manual  
included with the camcorder or camera for more detailed instructions.  
S
WB  
4-IN-1  
4-IN-1 A/V jack  
S-Video  
connector  
B
R
W
Y
4-IN-1 A/V cable  
AV connectors  
Note  
The cables are color-coded (black, red, white, yellow). Connect each color-  
coded cable to the appropriate connector on your device.  
26  
 
 
Connecting to a Video Game Console  
The instructions presented here are a general guide to connecting the TV to  
a game console using the RCA Jacks (some game devices may require a  
unique adapter that is not provided). Actual connections may vary according  
to the make and model of the game device. Refer to the user’s manual  
included with the game console for more detailed instructions.  
4-IN-1  
4-IN-1 A/V jack  
AV  
B R W Y  
connectors  
S-Video  
connector  
4-IN-1 A/V cable  
Notes  
Connect the 4-IN-1 A/V cable connectors to the corresponding  
connectors on your game device adapter.  
If the 4-IN-1 A/V cable does not fit the game device, then insert RCA jack  
between the 4-IN-1 A/V cable and game device.  
27  
 
 
Connecting External Speakers or Headphones  
External speakers or headphones may be used to listen to the TV rather  
than using the built-in speakers. Connect external speakers to the speaker  
line out port or headphones to the headphone port as illustrated.  
Headphones  
HEADPHONE  
Headphone/  
Speakers jack  
Speakers  
Notes  
External speakers or headphones are not included with the TV.  
The internal TV speakers will not output sound when headphones are  
plugged in.  
Use external speakers with built-in amplifiers only.  
28  
 
 
Connecting the Power Adapter  
1
Connect the power cord to the power adapter as illustrated.  
2 Plug the power adapter connector into the DC-IN input jack on the  
rear panel of the TV.  
3 Insert the three-pronged plug at the other end of the power cord into  
a power outlet.  
Three-pronged  
plug  
Power outlet  
DC-IN  
DC-IN  
Power cord  
Power adapter  
29  
 
 
9
Using the TV  
Using the Remote Control  
For best results, use the remote control within a distance of 16 feet  
(5 meters) from the front of the TV. Do not exceed an angle of 30 degrees  
when pointing at the TV.  
Notes  
The operational distance may be shortened when the signal sensor is  
directly exposed to strong light.  
Aim the transmitter on the remote control at the signal sensor and  
ensure that there are no obstacles between them.  
Turning the TV On and Off  
1
Press power  
TV.  
on the remote control or control panel to turn on the  
2 Press power  
again; the TV is in off mode.  
Selecting Channels  
Press channel up or channel down on the control panel to select the  
channel or enter the specific channel number by pressing the number  
buttons on the remote control.  
Switching Source Signals  
Press source to select the incoming source signal.  
The current source setting (TV/CATV, AV or S-Video) appears on the upper  
left corner of the screen.  
Adjusting the Volume  
Press volume up to increase the volume. Press volume down to decrease  
the volume. The volume level is displayed on the screen.  
30  
 
             
10 Adjusting On-Screen Display (OSD)  
Settings  
The On-Screen Display (OSD) menu system provides a quick and simple  
method to adjust your TV’s settings. This chapter describes how to change  
each of the available settings.  
The OSD can be used with either the remote control or the control panel.  
Function  
Menu  
Control Panel Icon  
Menu  
Button  
Menu  
Remote Control Icon  
MENU/ENTER, M  
Channel  
up  
Right arrow  
CH ( + / S / X)  
/ X  
Channel  
down  
Left arrow  
Enter  
CH ( – / T / W)  
/ W  
Enter  
Menu  
MENU/ENTER, M  
Note  
The following sections explain how to adjust settings in the OSD menus  
using the control panel.  
31  
 
 
OSD Setting Menu  
Main Menu  
ETO  
Press menu to enter the OSD  
menus.  
Brightness  
50  
The Main menu appears  
ENTER  
Note  
To exit the OSD menus, press channel up or channel down to select Exit  
. Then press menu to exit the OSD menus. Also, after you finish setting  
OSD parameters, follow these instructions to exit the OSD menus.  
32  
 
 
Brightness  
1
Press menu to enter the OSD menus.  
Main Menu  
ETO  
2 Press menu again and the brightness  
slide bar appears.  
Brightness  
50  
3 Press channel up to increase the  
brightness.  
ENTER  
4 Press channel down to decrease the  
brightness.  
5 Press menu to confirm the setting  
and return to the Main menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
33  
 
 
Contrast  
1
Press menu to enter the OSD menus.  
Main Menu  
ETO  
2 Press channel up or channel down to  
select Contrast.  
Contrast  
50  
3 Press menu. The contrast slide bar  
appears.  
ENTER  
4 Press channel up to increase the  
contrast.  
5 Press channel down to decrease the  
contrast.  
6 Press menu to confirm the setting  
and return to the Main menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
34  
 
 
Video Setting  
Press menu to enter the OSD  
menus.  
Main Menu  
ETO  
1
Press channel up or channel  
Video Setting  
down to select Video Setting.  
2 Press menu to enter the Video  
Setting menu.  
ENTER  
35  
 
 
Hue  
1
Press menu to enter the Hue menu.  
Video Setting  
G
R
B
2 Press channel up to increase the hue  
towards the red spectrum. The  
image becomes more red.  
Hue  
G
R
50  
3 Press channel down to decrease the  
hue towards the green spectrum.  
The image becomes more green.  
4 Press menu to confirm the setting  
and return to the Video Setting  
menu.  
ENTER  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
36  
 
 
Saturation  
1
Press channel up or channel down to  
select Saturation.  
Video Setting  
G
R
B
Saturation  
2 Press menu to enter the Saturation  
menu.  
50  
3 Press channel up to increase the  
saturation. The screen image  
becomes more vibrant.  
ENTER  
4 Press channel down to decrease the  
saturation. The screen image  
becomes less vibrant.  
5 Press menu to confirm the setting  
and return to the Video Setting  
menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
37  
 
 
Sharpness  
Video Setting  
1
Press channel up or channel down to  
select Sharpness.  
G
R
B
Sharpness  
2 Press menu to enter the Sharpness  
menu.  
50  
3 Press channel up to increase the  
sharpness.  
ENTER  
4 Press channel down to decrease the  
sharpness.  
5 Press menu again to confirm the  
setting and return to the Video  
Setting menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
38  
 
 
Color Temperature  
Video Setting  
1
Press channel up or channel down to  
select Color.  
G
R
B
Color  
2 Press menu to enter the Color menu.  
The following three color  
temperatures are available.  
ENTER  
Standard Color  
Press channel up or channel down to  
select Standard, then press menu.  
Warm Color  
Press channel up or channel down to  
select Warm, then press menu.  
Cold Color  
Press channel up or channel down to  
select Cold, then press menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
39  
 
 
Audio Setting  
Press menu to enter the OSD  
menus.  
Main menu  
ETO  
1
Press channel up or channel  
Audio Setting  
down to select Audio Setting.  
2 Press menu to enter the Audio  
Setting menu.  
ENTER  
40  
 
 
Treble  
1
Press menu to enter the Treble menu.  
Audio Setting  
Treble  
2 Press channel up to increase the  
treble.  
48  
3 Press channel down to decrease the  
treble.  
ENTER  
4 Press menu to confirm the setting  
and return to the Audio Setting  
menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
41  
 
 
Bass  
1
Press channel up or channel down to  
select Bass.  
Audio Setting  
Bass  
2 Press menu to enter the Bass menu.  
3 Press channel up to increase the  
bass.  
48  
ENTER  
4 Press channel down to decrease the  
bass.  
5 Press menu to confirm the setting  
and return to the Audio Setting  
menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
42  
 
 
Balance  
1
Press channel up or channel down to  
select Balance.  
Audio Setting  
Balance  
50  
2 Press menu to enter the Balance  
menu.  
L
R
3 Press channel up to shift the balance  
to the right speaker.  
ENTER  
4 Press channel down to shift the  
balance to the left speaker.  
5 Press menu to confirm the setting  
and return to the Audio Setting  
menu.  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
43  
 
 
TV Setting  
Press menu to enter the OSD  
menus.  
Main Menu  
ETO  
TV Setting  
1
Press channel up or channel  
down to select TV Setting.  
2 Press menu to enter the TV  
Setting menu.  
ENTER  
44  
 
 
TV/CATV  
TV Setting  
1
Press menu to enter the TV/CATV  
menu. The following choices are  
available.  
AUTO MENU  
SET SET  
Channel  
-
+
TV/CATV  
TV  
CATV  
Receiving Cable TV  
Press channel up to select CATV,  
then press menu.  
ENTER  
TV Setting  
AUTO MENU  
SET SET  
Channel  
-
+
Receiving Broadcast TV  
TV/CATV  
Press channel down to select TV  
(default), then press menu.  
CATV  
TV  
ENTER  
TV Setting  
AUTO MENU  
SET SET  
Channel  
-
+
TV/CATV  
CATV  
TV  
ENTER  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
45  
 
 
MTS  
TV Setting  
1
Press channel up or channel down to  
select MTS.  
AUTO MENU  
SET SET  
Channel  
-
+
MTS  
2 Press menu to enter the MTS menu.  
SAP Mono  
Stereo  
ENTER  
Stereo  
TV Setting  
AUTO MENU  
SET SET  
Channel  
-
+
1
Press channel down to select Stereo.  
Stereo is highlighted in red.  
MTS  
SAP Mono  
Stereo  
2 Press menu again to confirm the  
selection.  
ENTER  
SAP  
TV Setting  
AUTO MENU  
SET SET  
Channel  
-
+
1
Press channel up or channel down to  
select SAP. SAP is highlighted in red.  
MTS  
SAP Mono  
Stereo  
2 Press menu again to confirm the  
selection. This option may not be  
available in your local area.  
ENTER  
Mono  
TV Setting  
AUTO MENU  
SET SET  
Channel  
-
+
1
Press channel up to select Mono.  
Mono is highlighted in red.  
MTS  
2 Press menu to confirm Mono, which  
outputs sound through a single  
channel.  
SAP Mono  
Stereo  
ENTER  
Note  
The new setting is confirmed  
automatically when the OSD times out.  
46  
 
 
Auto Program  
TV Setting  
1
Press channel up or channel down to  
select Auto Program.  
AUTO MENU  
SET SET  
Channel  
-
+
AUTO Program  
2 Press menu to enter the Auto  
Program menu.  
NO  
YES  
3 Press channel up or channel down to  
select Yes or No.  
ENTER  
4 Press menu.  
Channel indicator values range from  
2 to 69 (antenna connection) or from  
1 to 125 (CATV cable connection).  
47  
 
   
Manual Program  
This function allows you to search preset channels or to erase previously  
preset channels.  
TV Setting  
1
Press channel up or channel down to  
select Manual Program.  
AUTO MENU  
SET SET  
Channel  
+-  
Manual Program  
2 Press menu to enter the Manual  
Program menu.  
Up  
DOWN  
3
3 Press channel up or channel down to  
find the channel you want to add.  
4 When you have found the channel,  
press menu.  
ENTER  
When you have found the channel, see  
the next section “Channel Add/Erase” to  
add or erase the channel.  
48  
 
 
Channel Add/Erase  
After you found a channel using Manual Program, follow the following  
instruction to add or erase the channel.  
1
Press channel up or channel down to  
select CH. Add/Erase.  
TV Setting  
AUTO MENU  
SET SET  
Channel  
-
+
CH.Add/Erase  
2 Press menu to enter the CH.  
Add/Erase menu. Select one of the  
following options.  
Add  
Erase  
3
ENTER  
Add Channel  
1
Press channel up to select Add.  
2 Press menu to add the selected  
channel.  
Erase Channel  
1
Press channel down to select Erase.  
2 Press menu to delete the selected  
channel.  
When you return to the normal TV  
screen and use channel up and  
channel down to browse channels,  
an erased channel (for example,  
Channel 3) is skipped automatically.  
Note  
You can still access the erased channel  
by entering the channel number using the  
number keys on the remote control.  
49  
 
 
Miscellaneous Setting  
Press menu to enter the OSD  
menus.  
Main Menu  
ETO  
1
Press channel up or channel  
down to select Miscellaneous  
Setting.  
Miscellaneous  
2 Press menu to enter the  
ENTER  
Miscellaneous Setting menu.  
50  
 
 
OSD Position  
1
Press menu to enter the OSD Position  
menu.  
Miscellaneous  
Z
CH  
Z
OSD  
Z
OSD Position  
The following options are available.  
ENTER  
Horizontal Position  
OSD Position  
1
2
Press menu.  
OSD  
OSD  
H - P o s i t i o n  
Press channel down to move the OSD  
screen to the left. Press channel up to  
move the OSD screen to the right.  
Press menu to confirm the setting.  
48  
ENTER  
3
Vertical Position  
OSD Position  
1
Press channel up or channel down to  
select V. Position.  
OSD  
OSD  
V- P o s i t i o n  
48  
2
3
Press menu.  
Press channel down to move the OSD  
screen downward. Press channel up  
to move the OSD screen upward.  
Press menu to confirm the setting.  
ENTER  
4
51  
 
 
Language  
Miscellaneous  
1
Press channel up or channel down to  
select Language.  
Z
Z
CH  
Z
OSD  
Language  
2 Press menu to enter the Language  
menu. The screen displays the  
available OSD languages: English  
and Español.  
English  
Espanol  
ENTER  
3 Press channel up or channel down to  
select a language.  
4 Press menu to confirm your choice.  
52  
 
 
Sleeper  
The Sleeper turns the TV off automatically after a set period of time.  
Miscellaneous  
1
Press channel up or channel down to  
select Sleep.  
Z
Z
Z
CH  
OSD  
Sleep  
2 Press menu to enter the Sleep menu.  
3 The screen displays the available  
sleep timer setting:  
30 60 90 120  
OFF  
ENTER  
– OFF  
– 30 minutes  
– 60 minutes  
– 90 minutes  
– 120 minutes  
Miscellaneous  
4 Press channel up or channel down to  
select a setting.  
Z
Z
Z
CH  
OSD  
Sleep  
5 Press menu to confirm your choice.  
30 60 90 120  
OFF  
ENTER  
53  
 
 
OSD Display  
When set to Off, the OSD display (source data on top left corner of the TV  
screen) turns off after approximately 5 seconds. When set to On, the OSD  
does not turn off automatically.  
Miscellaneous  
1
Press channel up or channel down to  
select OSD Display.  
Z
Z
CH  
Z
OSD  
OSD Display  
Off  
2 Press menu to enter the OSD  
Display menu.  
On  
3 Press channel up or channel down to  
select On or Off.  
ENTER  
4 Press menu to confirm your choice.  
54  
 
 
Reset  
The Reset function returns all of your TV’s user settings to their factory  
defaults.  
Warning:  
The reset function will erase all of your custom settings, and will reset  
all display settings (such as contrast, brightness, etc.) to the factory  
default values. The reset function cannot be reversed once it begins.  
Miscellaneous  
1
Press channel up or channel down to  
select Reset.  
Z
Z
CH  
Z
OSD  
Reset  
2 Press menu to enter the Reset menu.  
3 Press channel up or channel down to  
select Yes or No. By default, No is  
No  
Yes  
ENTER  
already selected (highlighted in red).  
4 Press menu to confirm your choice.  
55  
 
 
11 Taking Care of Your TV & Remote  
Control  
Turn the power off before you begin cleaning the  
TV.  
For best results, use a clean lens cloth to  
remove dust and fingerprints from the screen.  
Do not wipe the shell of the TV with alcohol,  
methanol, gasoline or oil products to avoid  
GAS  
OIL  
damaging the finish. Wipe the shell with a dry  
soft cloth and use neutral cleaning fluids.  
If your model has leather components, wipe the  
leather parts with a dry cloth and keep the area  
dry. Place the TV far from sources of steam to  
avoid making the leather wet.  
Be careful to disconnect the power plug  
correctly. Hold the plug. Do not attempt to  
disconnect the plug by pulling on the power cord.  
Arrange and store the power cord neatly as  
shown to the left to avoid knotting or bending  
which may cause fire due to damage or electric  
leakage.  
Note  
Protect the remote control from shock or vibration to avoid damage.  
Do not place the remote control in hot or humid locations.  
56  
 
 
12  
Troubleshooting  
Situation  
Solution  
Connect the power cord properly.  
Check if the power LED is on or not.  
Press power on the control panel or remote  
control.  
Press source to cycle through connected  
video sources.  
No picture and sound.  
Press channel up or channel down to  
switch to other TV stations.  
Check the TV/CATV OSD settings. See  
Make sure all cables are connected  
properly.  
Check the antenna and cable connections.  
Adjust the brightness in the OSD menus.  
No picture, or poor picture, sound is OK.  
Picture is not in color.  
Adjust the saturation in the OSD menus.  
Make sure all the cables are connected  
properly.  
Make sure the source device is functioning  
properly.  
Make sure the audio cable is connected  
securely.  
Picture is OK, no sound.  
Turn the mute off.  
Press volume up on the control panel or  
remote control.  
Make sure the MTS option is set to Stereo,  
Adjust the balance in the OSD menus. See  
Make sure the audio cable is connected  
securely.  
One of the speakers has no sound.  
Try the Auto Program function in the OSD  
Cannot receive some TV channels using  
cable TV.  
Use the Reset function in the OSD menu.  
Want to reset TV settings.  
57  
 
 
Situation  
Solution  
If OSD items are colored in light blue, the  
system is in a state such that those settings  
are not available.  
Cannot operate menus.  
Make sure the video signal cable is  
connected properly.  
Screen image turns over.  
Adjust the location of the antenna, placing it  
far from roads or sources of interference.  
Check the antenna and the video signal line  
connections.  
Snow appears on the screen.  
Readjust the sharpness setting.  
Choose programs with high quality signals.  
Adjust the direction of the antenna or  
change the video signal cable.  
Blurred or overlapped images.  
Remote control doesn’t work.  
Make sure the battery is inserted correctly.  
Replace the battery with a new one.  
Make sure the TV power cord is plugged in.  
Make sure the path between the remote  
control and the sensor is clear.  
Try operating the remote control at a closer  
distance to the TV. Refer to “Using the  
58  
 
13  
Warranty and Service  
For complete warranty service information, please refer to the “Warranty  
and Service Manual” enclosed with your TV.  
59  
 
 
14  
Specifications  
9.6 / 12.1-inch LCD TV  
LCD Panel Size  
Aspect Ratio  
9.6 / 12.1-inch TFT  
4:3  
Display Resolution  
TV System  
800 (horizontal) x 600 (vertical)  
NTSC  
S-Video Input and Composite Video  
Input (through the 4-IN-1 A/V cable)  
Video System  
Audio System  
Input: RCA Jack (L/R Audio Input with  
the 4-IN-1 A/V cable)  
Output: 3.5mm ø headphone jack x 1  
Built-in Speakers  
Power Supply  
2W + 2W / 3W + 3W  
100-240V, 50/60 Hz, 12V DC  
60 W Maximum  
Power Consumption  
Optional Accessories  
External Speakers  
60  
 
 
15  
Glossary  
Aspect Ratio: The ratio of width to height of a film, image or display  
screen.  
Broadcast TV: Broadcasting video signals using high-frequency  
electromagnetic waves to distribute television channels to viewers  
(standard TV broadcast).  
CATV: Community Antenna Television, the original name for cable  
TV. A television distribution system that uses coaxial cable instead of  
the traditional radio broadcasting (over-the-air) method to deliver  
television, FM radio, and other services to consumers.  
Color Temperature: Adjusting the color temperature enables you to  
set the intensity of white light. Color temperature is measured in  
Kelvin (K). Higher color temperatures result in a blue tint. Lower  
temperatures result in a red tint.  
Hue: Colors in a color system are measured by hue, saturation and  
luminance. Hue indicates the predominant color.  
LCD (Liquid Crystal Display): A display technology that uses rod-  
shaped molecules (liquid crystals) that flow like liquid and bend light.  
MTS: Multi-channel Television Sound. Enables reception of audio  
other than the primary (stereo) audio signal. SAP (Second Audio  
Program) enables reception of a separate channel that may be a  
different language or completely different information such as the  
news.  
OSD (On-Screen Display): A control panel on the television screen that  
allows you to select viewing options.  
Saturation: Chromatic purity indicating the amount of white contained  
in a color. Fully saturated colors are pure colors; less saturated  
colors appear as pastel shades.  
Stereo: is the default audio signal belonging to a particular channel.  
S-Video: Separate video, a video cabling standard used to transmit  
video by keeping brightness (Y) and color information (C) on  
61  
 
 
separate channels. Most often used with camcorders, VCRs, and  
quality receivers and amplifiers to provide sharper pictures.  
62  
 

Hamilton Beach Oven 22703 User Manual
Hamilton Beach Toaster 22709C User Manual
Hans Grohe Indoor Furnishings 35115801 User Manual
Harbor Freight Tools Cordless Drill 68147 User Manual
Hoshizaki Ice Maker F 80 I MAH c User Manual
Hotpoint Dishwasher BFI 680 User Manual
Hotpoint Microwave Oven SY10 User Manual
HP Hewlett Packard Digital Camera R725 User Manual
HP Hewlett Packard Network Router 8711A User Manual
IBM Printer 1725 SLS User Manual