Haier Dishwasher HDW100SCT User Manual

Dishwasher  
HDW100WCT  
HDW100SCT  
Instructions for Use  
0120505591  
 
Safety Is Very Important  
Carefully read the instructions contained in this manual, as it provides information that is essential to safe  
and proper installation, use and maintenance of this appliance.  
Carefully remove and dispose of the packing material.  
Check to make sure that the appliance is not damaged. If in doubt, contact the retailer it was purchased  
from.  
This dishwasher is designed for washing household dishes and cooking utensils.  
Do not install this appliance outdoors, even if a roof covers the area.  
Do not lean or sit on the door when it is open, as it may over turn the dishwasher.  
Do not touch the heating element during or after a wash cycle.  
If the appliance malfunctions, turn off water supply to the appliance and disconnect the plug from the wall  
socket and refer to the section entitled, "Troubleshooting". If you cannot solve the problem, contact an  
authorised service centre/agent.  
Only selected service centres/agents are authorised to make repairs.  
If the supply cord is damaged ,it must be replaced by the manufacture, a service agent of similar qualified  
persons in order to avoid a hazard.  
The appliance is not instruct for use of young children of infirm persons without supervision. Young  
children should be supervised to ensure that they do not play with the appliance.  
Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid con-  
tact with the skin and eyes and keep children away from the dishwasher when the door is open. Check  
that the detergent receptacle is empty after completion of the wash cycle.  
Do not use extension cords or multiple sockets.  
The plug must be accessible after installation.  
During installation the power cord must not be bent or flattened excessively.  
If the appliance is not operating properly,disconnect the appliance from the power supply.  
Warning  
Dishwasher detergents can be extremely dangerous if swallowed. Avoid contact with skin,  
eyes and keep children away from the dishwasher when the door is open. Check that the  
detergent receptacle is empty after completion of the wash cycle.  
To maintain the EFFICIENCY and SAFETY of this appliance:  
Only call a authorised service centre.  
Always use original Spare Parts.  
Children and infirm must be supervised at all times during use of the dishwasher by an adult.  
2
 
Close-up View (Control Panel)  
"POWER" Button  
"END" Light  
Handle For Opening Door  
Knob For Selecting Cycle  
A
B
C
D
Close-up View (Interior)  
Upper Rack  
Bottom Spray Arm  
A
B
C
D
E
Rack Height Adjustor  
Top Spray Arm  
Lower Rack  
Washing Filter  
F
Detergent and Rinse Aid Dispenser  
G
3
 
Detergent and Rinse Aid...  
Detergent  
Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled be-  
fore the start of each wash cycle following the instructions provided in the "Wash Cycle Table." The deter-  
gent dispenser is located on the inside panel the door.  
B
Loading the detergent  
To open the "A" cover on the dispenser, press the "B" button. The  
detergent for the wash cycle should be poured into the "C"  
compartment.The detergent for the pre-wash cycle should be poured  
into the “D” compartment.  
After the detergent has been placed in the dispenser, close the cover  
and press down until it clicks in place.  
D
C
A
Notice:  
To facilitate closing the cover, remove any excess detergent on the edges of the dispenser.  
Dishwasher detergents are stronly alkaline. They can be extremely dangerous if swallowed.  
Avoid contact with the skin and eyes and keep children away from the dishwasher when the  
door is open. Check that the detergent receptable is empty after completion of the wash cycle.  
Rinse Aid  
This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the  
inside panel of the door and should be filled after every 80 wash cycle (or when the rinse aid indicator light  
comes on for models with this feature).  
Loading the Rinse Aid  
To open the dispenser, turn the "E" cap in an anti-clockwise direction  
and then pour in the rinse aid, making sure not to overfill. The amount  
of rinse aid used for each cycle, turn the dosage adjuster "F", beneath  
E
the cap, with a screwdriver. There are 6 different settings; the normal  
dosage setting is 3.  
Important  
Proper dosage of the rinse aid improves drying.  
F
If drops of water remain on the dishes or spotting occurs, the dosage adjuster should be turned to a higher  
setting.  
If the dishes have white streaks, turn the dosage adjuster to a lower setting.  
4
 
Loading the Dishwasher  
Before placing the dishes in the dishwasher, remove the larger food  
particles to prevent the filter from becoming clogged.  
If the pots and pans have baked-on food that is extremely hard to remove,  
we recommend they are soaked before washing. This will eliminate the  
need for extra wash cycles.  
Lower Rack  
Pull out the rack to load the dishwasher.  
The lower rack  
Place the most difficult to clean items on the bottom rack: pots, pans,  
lids, serving dishes and bowls.  
Upper Rack  
It is preferable to place serving dishes and lids on the sides of the racks  
in order to avoid blocking the rotation of the top spray arm.  
- Pots, serving bowls, etc. must always be placed face down.  
- Deep pots should be tilted to allow the water to flow out.  
The upper rack  
The upper rack is designed to hold more delicate and lighter dishes,  
such as glasses, cups and saucers, plates and small bowls.  
- Position the dishes so that they do not move by the spray of the water.  
To adjust the height of the upper rack, rotate the caps located on the  
end of the rack guide rails to the side, remove the rack-  
Load for 12 Standard Settings  
completely and refit using the alternate set of wheels (see fig.B).  
Adjust the upper basket to the higher level to allow more height in  
the bottom basket for large items.  
Information on comparability tests imple-  
mented in compliance with AS/NZS 2007  
fig.A  
Appliance loaded in accordance with standard specifications.  
Example of loaded dishwasher: See fig. A and B.  
Capacity: 12 place settings  
Comparability programme: NORMAL wash  
Rinse-aid setting: 5  
Detergent: 25+5g  
Height-adjustable top-basket must be inserted in the uppermost position.  
If the comparability tests do not comply fully with AS/NZS 2007, e.g.,  
degree of soiling, type of dishes  
fig.B  
and cutlery, etc., contact the appliance manufacturer before starting the  
test.  
5
 
Turning on the Appliance  
Starting a wash cycle...  
Make sure that the plug for the appliance is inserted into the wall socket.  
Make sure that the water supply is turned on to full pressure.  
Load the dishes.  
Pour in the detergent.  
Press the "POWER" button, and the “END” light will turn on.  
Turn the knob located on the right of the control panel until the number or symbol for the cycle setting is  
aligned with the refrence mark (see the section entitled, program overview).If the knob rightly aligned with  
the refrence mark you want to choose, you must turn the knob to with the mark of “RESET” .Then back to  
first step.  
After five seconds the “END” light will turn off, the wash cycle will begin.  
Notice:  
When washing, the knob will not rotate itself.  
At the end of the wash cycle...  
When the buzzer constantly beeps six times, the “END” light will turn on and the cycle has finished. Turn off  
the appliance using the "POWER" button, turn off the water supply and open the door of the dishwasher.  
Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are  
still hot and more susceptible to breakage. They will also dry better.  
Cancelling or modifying a wash cycle setting...  
A cycle that is underway can only be modified if it has been running for a short time. Otherwise, the detergent  
may have already been used, and the appliance may have already drained the wash water. If this is the  
case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent").Rotate  
the knob to the mark of “RESET” then select right programme.  
6
 
Energy Saving Tips  
It is important to try and run the dishwasher when it is fully loaded to save on energy.  
Rather than run a full cycle for a half load, you can run the "PRE-RINSE" cycle which will prevent odours  
from forming and food from caking onto the dishes.  
Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils  
being washed and how dirty they are.  
Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but,  
rather, a greater negative impact on the environment.  
How to Keep Your Dishwasher in Shape  
After Every Wash  
After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture  
and odors are not trapped inside.  
Remove the Plug  
Before cleaning or performing maintenance, always remove the plug from the socket.  
Solvents or Abrasive Cleaning Products  
Do not use solvents or abrasive cleaning products to clean the exterior and rubber parts of the dishwasher,  
use only a cloth and warm soapy water.  
To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white  
vinegar, or a cleaning product made specifically for dishwashers.  
Moving the Appliance  
If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be laid  
on its back.  
DO NOT LAY THE MACHINE ON ITS RIGHT HAND SIDE  
Seals  
One of the reasons that odours form in the dishwasher is that food get trapped in the seals. Periodic clean-  
ing with a sponge will prevent this.  
When You Go on Holiday  
When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then  
remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar.  
This will help the seals last longer and prevent odours from forming.  
7
 
Wash Cycle Table  
Detergent  
Rinse  
Aid  
Wash  
Description of cycle  
Types of load  
programme  
Extended  
Wash  
Prewash  
Very dirty dishes,  
Pre-wash with hot water.  
Extended wash at 70°C.  
Rinses with cold water.  
Rinse with hot water.  
Drying.  
pots and pans. (Not  
HEAVY  
25g  
5g  
to be used with deli-  
cate items.)  
Pre-wash use cold water.  
Extended wash at 50°C.  
Rinse with cold water.  
Rinse with hot water.  
Drying.  
Normal load of dirty  
NORMAL  
dishes, pots and  
pans, Standard daily  
cycle.  
5g  
5g  
25g  
25g  
( )  
(AS/NZS 2007)  
Pre-wash use cold water.  
Extended wash at 50°C.  
Rinse with cold water.  
Rinse with hot water.  
Drying.  
Lightly soiled deli-  
cate items.  
LIGHT  
Economic cycle for  
delicate items. Run  
immediately after  
dishes are used.  
Wash at 45°C.  
Rinse with cold water.  
Hot rinse.  
GLASSWARE  
25g  
15g  
Drying.  
Short wash at 40°C.  
Cold rinse.  
Very lightly solied  
mixed dishes.  
FAST  
For dishes that only  
require a rinse and  
dry.  
Hot rinse at 65°C.  
Drying.  
RINSE  
15g  
Pre-rinse of dishes  
Short cold wash to pre-  
PRE-RINSE  
while waiting for a vent food residue from  
full load. drying on the dishes.  
( ) AS/NZS 2007 test with rinse aid setting 5  
8
 
Cleaning and Special Maintenance  
Filter Assembly  
For the best performance and results, the filter assembly must be keep clean.  
The filter removes food particles from the wash water, allowing the water to be recirculated during the cycle.  
For this reason, it is a good idea to remove any food particles trapped in the filter after each wash cycle by  
rinsing the semi-circular filter and cup "A" under running water. To remove the filter assembly, pull the  
handle in an upward direction. The entire filter assembly (made up of the semicircular filter "A" and the fine  
filter "B") should be cleaned at least once a month use a soft brush. To reassemble, insert the entire assem-  
bly into the dishwasher, locate it correctly in its seat and pressing downward.  
The dishwasher must not be used without the filters. Improper replacement of the filters may reduce the  
performance of the appliance.  
A
B
Cleaning the Spray Arms  
Food particles may become encrusted on the spray arms and block the hole (see "Close up view [interior]"  
on page 3, letters C-E ). Check the spray arms periodically and clean them when needed.  
Troubleshooting  
Resolving minor problems yourself  
Experience has shown that you can resolve most problems that rise during normal daily usage yourself,  
without having to call out a service engineer.Not only does this save costs,but it also means that the appli-  
ance is available for use again that much sooner. The following list of common occurrences and their rem-  
edies should help you identify the causes of most problems.  
Problems...  
...when the appliance is switched on  
Appliance does not start up  
9
 
Troubleshooting  
Fault with fuse in mains electricity supply.  
Plug not inserted in wall socket.  
Appliance door not closed properly.  
Knob stay at the mark of "RESET"  
Water tap not turned on.  
Blocked strainer in water intake hose.  
- The strainer is situated in the Aquastop or supply-hose connection.  
Caution  
Do not forget that repairs should only be carried out by a qualified specialist. Improper repairs  
can lead to considerable equipment damage as well as danger to the user.  
...with the appliance itself  
When the alarm sounds in a series of 2 beeps, pause, 2 beeps, pause ...  
the water is turned on and the hose is connected properly;  
the water supply to the house is on and has sufficient pressure;  
the water supply hose is crimped or bent;  
the filter for the water supply hose is clogged.  
the drain hose is too low.  
When the alarm sounds in a series of 3 beeps, pause, 3 beeps, pause ...  
the drain hose is crimped or bent.  
the drain hose is too high.  
When the alarm sounds in a series of 4 beeps, pause, 4 beeps, pause ...  
Temperature sensor failed and call your Authorised Service Center.  
When the alarm sounds in a series of 5 beeps, pause, 5 beeps, pause ...  
Flood switch has been activated and call you Authorised Service centre.  
When the alarm sounds in a series of 6 beeps, pause, 6 beeps, pause ...  
the drain hose is too low.  
When the "END" indicator is on, at the moment, the alarm sounds in a series of 7 beeps,  
pause, 7 beeps, pause ...  
the door is not properly closed.  
If you take all these checks and the dishwasher still does not function or your dishwasher  
have any other error display, you can power the dishwasher OFF, and wait a few minutes.  
You can power the dishwasher on, try it again, if the dishwasher still does not function and/  
or the problem persists, contact the nearest authorised service center and provide them  
with the following information:  
10  
 
Troubleshooting  
the nature of the problem.  
the model type number (Mod...) And the serial number (S/N...), which are indicated on the plate located  
on the side of the inner part of the door.  
Lower spray arm rotates with difficulty  
Spray arm is blocked by small items or food remains.  
Lid in detergent compartment cannot be closed  
Detergent compartment has been overfilled.  
Mechanism is clogged with remnants of detergent.  
Remnants of detergent stuck inside dispenser  
Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent  
is added.  
Water remains inside appliance after programme has ended  
Blockage or kind in drainage hose.  
Pump is jammed.  
Filters are blocked.  
The programme is still running. Wait for the programme to end.  
...during washing  
Unusual amount of foam is creased  
Normal washing up liquid has been poured into the rinse-aid container.  
Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next  
washing cycle.  
Appliance stops suddenly while washing is taking place  
Cut off electricity supply to appliance.  
Water supply has been interrupted.  
Knocking sound can be heared while washing is taking place  
A spray arm is knocking against the dishes inside the appliance.  
Rattling sound can be heared while washing is taking place  
Crockery has not been stacked properly inside the appliance.  
Knocking sound coming from inlet valves  
This is caused by the way the water pipes have been laid and it has no effect upon the way the appliance  
functions. There is no remedy for this.  
11  
 
Troubleshooting  
...with the dishes,cutlery, etc.  
Remnants of food are stuck to the dishes, cutlery,etc.  
Dishwasher was not loaded properly. Jets of water could not reach all parts of the dishes, etc.  
Too many items in the rack.  
Items in the rack were touching each other.  
Not enough detergent was added to dispenser.  
Selected wash programme was not intensive enough.  
Rotation of spray arm was obstructed by dishes, etc.  
Nozzles in spray arm are blocked by remnants of food.  
Filters are blocked.  
Filters have been incorrectly fitted.  
Waste-water pump is jammed.  
Plastic items are discoloured  
Not enough detergent was added to dispenser.  
Detergent has insuffcient bleaching properties. Use a detergent containing a chemical bleaching agent.  
White stains are left on crockery, glasses have a milky appearance  
Not enough detergent was added to dispenser compartment.  
Amount of rinse-aid was set too low.  
Although water is quite hard, no salt has been put in appliance.  
Water softener was set too low.  
If you used a phosphate-free detergent , try a detergent containing phosphates and compare results.  
Dishes,cultlery,etc.have not been dried  
Selected programme did not include drying function.  
Amount of rinse-aid was set too low.  
Items were removed from dishwasher too soon.  
Glasses have a dull appearance  
Amount of rinse-aid was set too low.  
Tea stains or traces of lipstick have not been completely removed  
Detergent does not have a sufficient bleaching effect.  
Washing temperature was set too low.  
Traces of rust on cutlery  
Cutlery is not sufficiently rustproof.  
Glasses become clouded and discoloured; coating cannot be wiped off  
Unsuitable detergent was used.  
Glasses are not dishwasher-proof.  
Smears left behind on glasses and cutlery; glasses have acquired a metallic appearance  
Amount of rinse-aid set too high.  
12  
 
Installation  
Positioning the Appliance  
Position the appliance in the desired location. The dishwasher is equipped with water supply and drain  
hoses that can be positioned to the right or left to allow correct installation.  
Levelling the Appliance  
Once the appliance is positioned, adjust the feet by screwing them in or out. The appliance should not be  
inclined more than 2 degrees, to ensure proper performance.  
Cold Water Connection  
Connect the cold water supply hose to a threaded 3/4 bsp connector and make sure that it is fastened tightly  
(see fig.1).  
If the water pipes are new or have not been used for an extended period of time, let the water run first, till it  
is clear and free of impurities. Otherwise the water inlet filter may get blocked.  
Hot Water Connection  
The appliance can also be connected to the house's hot water supply following the same procedure as for  
the cold water connection.  
DO NOT CONNECT TO A PUSH THROUGH HOT WATER SYSTEM  
OR ONE THAT EXCEEDS A TEMPERATURE OF 60OC.  
fig.1  
13  
 
Installation  
Drain Hose Connection  
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink. Use the  
plastic support that comes with the appliance (see fig .2) and ensure there are no tight bends or kinks. The  
free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water.  
MAX 100  
MIN 40  
fig.2  
Attention:  
The plastic hose support must be fastened to the wall to prevent the drain hose from moving.  
Electrical Connection  
After making sure that the voltage and frequency in the home correspond to those on the rating plate of the  
appliance (located on the side of the stainless steel inner door) and that the electrical system can cope with  
the maximum voltage on the rating plate,insert thr plug into an earthed electrical socket.  
DO NOT USE ADAPTORS OR EXTENSION LEADS.  
14  
 
Technical data  
60 cm  
60 cm  
Width  
Depth  
85 cm  
Height  
Capacity  
12 standard place settings  
0.03-1.0 MPa  
220-240V~ 50Hz  
1950W  
Mains water pressure  
Power voltage  
Total absorber power  
Diagram  
15  
 

Grizzly Lathe G0602 User Manual
Haier Washer XQB60 91BF User Manual
HannsG Flat Panel Television HG281 User Manual
Hoshizaki Ice Maker C 100BAF User Manual
Hotpoint Dishwasher FDYF 11011 Style User Manual
HP Hewlett Packard Computer Drive 40 SCSI User Manual
HP Hewlett Packard Scanner 4400C User Manual
Iiyama Computer Monitor LM704UT User Manual
iLive Music Mixer AP6526 User Manual
Impex Home Gym SM 600 User Manual