iLive MP3 Docking Station ITP280B User Manual

USER’S GUIDE  
V:1041-0208-10  
ITP280B  
Bar Speaker for iPhone/iPod  
For the most up-to-date version of this Users Guide, go to www.ilive.net  
 
fcc Warnings  
NOTE: This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide reason-  
able protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in ac-  
cordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or televi-  
sion reception, which can be determined by turning the equip-  
ment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and re-  
ceiver.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician  
for help.  
additional Warnings  
• The apparatus shall not be exposed to dripping or splashing  
and that no objects filled with liquids, such as vases, shall be  
placed on apparatus.  
L’appareil ne doit pas être exposé aux écoulements ou aux  
éclaboussures et aucun objet ne contenant de liquide, tel  
qu’un vase, ne doit être placé sur l’objet.  
• Main plug is used as disconnect device and it should remain  
readily operable during intended use. In order to disconnect  
the apparatus from the mains completely, the mains plug  
should be disconnected form the mains socket outlet com-  
pletely.  
La prise du secteur ne doit pas être obstruée ou doit être  
facilement accessible pendant son utilisation. Pour être com-  
plètement déconnecté de l’alimentation d’entrée, la prise  
doit être débranchée du secteur.  
• Battery shall not be exposed to excessive heat such as sun-  
shine, fire or the like.  
Les piles ne doivent pas être exposées à de forte chaleur, tel  
qu’à la lumière du soleil, au feu ou autres choses de sem-  
blable.  
• Caution marking is located at the rear of the apparatus.  
Les marquages sont inscrits en bas de l’appareil.  
• The marking information is located at the bottom of appara-  
tus.  
Les précautions d’emploi sont inscrites en bas de l’appareil.  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
3
 
Bar sPeaker for iPhone/iPod  
features  
• Works with iPhone  
• Made for iPod  
• Video output  
• Line input (3.5mm)  
• Auxiliary input (RCA)  
• Remote control  
• 37” length  
• FM radio  
• Station memory presets (20 FM)  
• Last channel memory  
• Treble and bass controls  
• 3.1 channel stereo system  
• Preset EQ  
• Subwoofer output  
• S-video output  
• 2 audio/video inputs  
• S-video output  
• Basic iPhone/iPod controls  
• Supports Universal docking brackets  
• Wall mountable  
• Digital clock  
• SRS TruSurround XT™ with simulated 5.1  
effect  
• Motorized iPod drawer  
• Cloth net speaker grill  
• AC power: built-in AC power cable  
• Timer  
• White LCD display  
• Sleep timer  
included  
• ITP280B  
• Remote control (batteries not included)  
• Docking brackets for iPhone/iPod (6)  
• AC power cable  
• FM wire antenna  
• Wall-mount hardware  
4
iLive | ITP280B  
 
taBLe of contents  
introduction  
6
8
setuP  
cLock, aLarM, and sLeeP tiMer  
iPhone/iPod and radio  
aV1, aV2, auXiLiary inPut, Line inPut, eQ  
Basic connectiVity  
9
10  
11  
12  
13  
14  
16  
connecting the Bar sPeaker to a tV  
Mounting the Bar sPeaker to a WaLL  
coMPany inforMation  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
5
 
introduction  
PoWer  
Press to turn the bar speaker  
off or on.  
VoLuMe  
Press to adjust the volume.  
source  
Press to switch between iPod/  
iPhone, FM radio, AV1, AV2,  
Line, and AUX modes.  
PLay/Pause  
Press to play or pause a  
docked iPhone or iPod.  
iPod draWer  
Press to open and close the  
iPod docking drawer.  
Line inPut (3.5mm)  
Use to connect an MP3 player  
or other audio source to the  
bar speaker.  
reset  
Press using a paperclip or like  
object to reset the bar speaker  
to it’s original settings.  
Video outPut  
aV1 inPut  
suBWoofer outPut  
fM antenna connection  
s-Video outPut  
aV2 inPut  
rca auXiLiary audio  
inPuts  
6
iLive | ITP280B  
 
standBy/on  
Press to turn the bar speaker off or  
on.  
nuMBer keyPad  
iPod draWer  
Press to open or close the motorized  
drawer for iPhone and iPod.  
Mute  
Press to mute the volume of the bar  
speaker.  
rePeat  
Press to repeat the current track or  
entire album.  
aLarM  
With the power off, press to set and  
activate the alarm.  
Menu uP/doWn for iPod  
Press to navigate the menu on a  
docked iPhone or iPod.  
cLock  
With the power off, press to set the  
clock.  
treBLe  
In EQ mode MUSIC 2.1 or MUSIC 3.1,  
press to adjust the levels of treble.  
sLeeP  
Press repeatedly to set the sleep  
timer.  
seLect  
Press to make a selection on a  
docked iPhone or iPod.  
Bass  
In EQ mode MUSIC 2.1 or MUSIC 3.1,  
press to adjust the levels of bass.  
shuffLe  
Press to play music from a docked  
iPhone or iPod in a random order.  
reV/fWd for iPod/Min  
Press to rewind or fast forward  
content from a docked iPhone or  
iPod. Press to adjust the minute when  
setting the clock or alarm.  
eQ  
Press to cycle through MUSIC  
2.1, MUSIC 3.1, TruSurround XT,  
TruSurround XT-DC, and SRS-WOW  
equalizer modes.  
Menu  
Press to access the previous menu on  
a docked iPhone or iPod.  
PLay/Pause  
Press to play or pause a docked  
iPhone or iPod.  
skiP/tune  
Press to skip forwards or backwards  
through content on a docked iPhone  
or iPod. Press to tune the FM radio.  
VoLuMe  
Press to adjust the volume.  
aLBuM/chaPter/PLayList  
Press to cycle through albums,  
chapters, and playlists on a docked  
iPhone or iPod.  
stoP  
Press to stop an iPod during play.  
MeMory  
Press to cycle through FM radio  
presets.  
source  
Press to switch between FM radio,  
AV1, AV2, Line, and AUX modes.  
iPod  
Press to switch to iPod mode.  
disPLay  
Press to switch between the clock  
and current mode display.  
MeM  
Press to save the current FM radio  
station as a preset.  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
7
 
setuP  
Power  
Plug the attached AC cord into a standard AC  
power outlet to power the bar speaker.  
Battery Power  
Requires 2 AAA batteries (not included)  
8
iLive | ITP280B  
 
cLock, aLarM, and sLeeP tiMer  
setting the clock  
setting the sleep timer  
1 With the bar speaker powered on, press the  
sLeeP button repeatedly to set the sleep  
timer.  
1 Press the PoWer button to turn the bar  
speaker off.  
2 Press the cLock button on the remote.  
2 After the set amount of time expires, the bar  
speaker will automatically power off.  
The clock will begin to blink.  
3 Press the reV/fWd for iPod Min/hr  
buttons on the remote to adjust the hour  
and minute.  
4 Press the cLock button to finish setting the  
time.  
setting the alarm  
1 Press the PoWer button to turn the bar  
speaker off.  
2 Press the aLarM button on the remote.  
The alarm time will begin to blink.  
3 Press the reV/fWd for iPod Min/hr  
buttons on the remote to adjust the hour  
and minute.  
4 Press the source button to select FM or  
iPod mode for the alarm source.  
5 Press the aLarM button to finish setting  
the alarm time.  
6 Once set, the alarm will automatically be  
activated. Press the aLarM button an  
additional time, after setting the alarm, to  
deactivate the alarm.  
When the text ALARM appears on the display,  
the alarm is activated.  
7 After the alarm sounds, press the PoWer  
button to turn the alarm off.  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
9
 
iPhone/iPod and radio  
docking an iPhone/iPod  
tuning the fM radio  
1 Press the PoWer button to turn the bar  
speaker on.  
1 Press the PoWer button to turn the bar  
speaker on.  
2 Press the source button to switch to  
iPhone/iPod mode. (iPod button on the  
remote)  
2 Press the source button to switch to FM  
radio mode.  
3 Press the skiP/tune buttons on the  
3 Press the iPod draWer button to open the  
remote to tune the FM radio.  
MOTORIZED DOCK FOR iPhone/iPod.  
saving a station as a Preset  
4 Locate the numbered bracket that fits the  
iPhone/iPod model that will be docked.  
Each included bracket has a number on it,  
indicating which iPhone/iPod model that  
bracket is compatible with. See the separate  
bracket chart page to identify which bracket  
is needed.  
5 Snap the bracket into place over the  
iPhone/iPod connector in the motorized  
dock.  
1 Follow the instructions for TUNING THE FM  
RADIO.  
2 Press the MeM button.  
3 Press the Menu uP/doWn for iPod  
buttons to select a preset. (P01, P02, P03,  
etc.)  
4 After you’ve selected a preset, press the  
MeM button to save the current FM radio  
station to the selected preset.  
6 Connect the iPhone or iPod to the  
connector inside the Dock for iPhone/iPod.  
When the speaker is plugged in, using AC  
tuning to a Preset fM radio station  
power, the docked iPhone or iPod will charge.  
1 Follow the instructions for TUNING THE FM  
RADIO.  
2 Follow the instructions for SAVING A  
STATION AS A PRESET.  
3 Press the MeMory buttons on the remote  
to cycle through preset radio stations.  
Playing an iPhone/iPod  
1 Follow the instructions for docking an  
iPhone/iPod.  
2 Press the PLay/Pause button to begin  
playing music from the docked iPhone or  
iPod.  
10  
iLive | ITP280B  
 
aV1, aV2, auXiLiary inPut, Line inPut, and eQ  
Line input  
aV1 and aV2  
Requires an 3.5mm audio cable (not included)  
Requires an RCA audio/video cable (not  
included)  
1 Connect an RCA audio/video cable to the  
aV1 or aV2 inPuts. Connect the other end  
of the RCA cable to the audio/video outputs  
on a DVD player, stereo system, gaming  
system, etc.  
1 Connect 3.5mm audio cable to the Line  
inPut. Connect the other end of the  
3.5mm cable to an MP3 player or other  
audio source.  
2 Press the PoWer button to turn the bar  
speaker on.  
2 Press the PoWer button to turn the bar  
speaker on.  
3 Press the source button to switch to LINE  
mode.  
3 Press the source button to switch to AV1  
or AV2 mode.  
4 Use the native controls on the connected  
device to begin playing audio or video  
routed through the bar speaker.  
4 Use the native controls on the connected  
device to begin playing audio routed  
through the bar speaker.  
Built-in sound technologies  
Press the eQ button to cycle through the  
available equalizer settings.  
auxiliary input  
Requires an RCA audio cable (not included)  
srs trusurround Xt® creates a truly  
immersive surround sound experience with  
rich bass and clear dialog.  
srs trusurround Xt® - dialog clarity Mode  
enhances the vocals so dialog is clear and  
easy to understand.  
1 Connect an RCA audio cable to the  
auXiLiary inPuts. Connect the other end  
of the RCA cable to the audio outputs on a  
DVD player, stereo system, gaming system,  
television, etc.  
2 Press the PoWer button to turn the bar  
speaker on.  
3 Press the source button to switch to AUX  
mode.  
srs WoW® significantly improves the  
playback quality of audio, delivering a  
dynamic 3D entertainment experience with  
deep, rich bass.  
Music 2.1 delivers the audio through two of  
the three speakers and the subwoofer.  
Music 3.1 delivers the audio through all  
three of the bar speaker’s speakers and the  
subwoofer.  
4 Use the native controls on the connected  
device to begin playing audio routed  
through the bar speaker.  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
11  
 
Basic connectiVity  
Below, you’ll see a basic flow chart of how you can connect your home entertainment devices to  
the bar speaker, and in turn how the bar speaker connects to them.  
AUDIO  
S-VIDEO  
VIDEO  
AUDIO &/Or  
VIDEO  
AUDIO &/Or  
VIDEO  
AUDIO  
DVD PLAYER  
DIGITAL CABLE or SATELLITE TUNER  
GAMING CONSOLE  
VCR  
SUBWOOFER  
12  
iLive | ITP280B  
 
connecting the Bar sPeaker to a teLeVision  
composite Video output  
Requires an RCA audio/video cable (not  
included.  
TELEVISION  
VIDEO INPUT  
AUDIO OUTPUTS  
1 Plug an RCA audio/video cable into the  
COMPOSITE VIDEO OUTPUT (yellow)  
on the bar speaker and the composite  
video input (yellow) on a television.  
2 Plug the remaining plugs on the included  
RCA audio/video cable into the RCA  
AUXILIARY AUDIO INPUTS (red and  
white) on the bar speaker and the RCA  
stereo audio outputs (red and white) on a  
television.  
3 Adjust the television’s input setting to  
correspond to the inputs used when  
connecting the bar speaker.  
s-Video output  
Requires an RCA audio cable (not  
included.  
TELEVISION  
S-VIDEO INPUT  
AUDIO OUTPUTS  
Requires an S-video cable (not included)  
1 Plug an S-video cable into the S-VIDEO  
OUTPUT on the bar speaker and the  
S-video input on a television.  
2 Plug an RCA audio cable into the RCA  
AUXILIARY AUDIO INPUTS (red and  
white) on the bar speaker and the RCA  
stereo audio outputs (red and white) on a  
television.  
3 Adjust the television’s input setting to  
correspond to the inputs used when  
connecting the bar speaker.  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
13  
 
Mounting the Bar sPeaker to a WaLL  
important notes  
We recommend having this bar speaker  
professionally mounted.  
The included spacers should be used at  
your discretion to extend the face of the  
bar speaker farther from the wall. These  
are typically used when mounting the bar  
speaker under a television, and the face of the  
bar speaker needs to be flush with the face of  
the television.  
required tools  
Manual or Power Screwdriver  
Stud Finder  
Pencil  
Tape Measure  
Level  
included hardware  
(2) Wall Mount Brackets  
(4) Long Screws  
(4) Short Screws  
(2) 1/4Spacers  
(2) 1/2Spacers  
(2) 3/4Spacers  
14  
iLive | ITP280B  
 
Mounting the Bar sPeaker to a WaLL  
getting started  
studs  
1 Use the taPe Measure to decide how  
high you’d like to hang the bar speaker on  
the wall.  
The bar speaker must be hung within 6 feet of  
an AC power outlet for the attached AC power  
cable to reach.  
2 Use the stud finder to locate 2 parallel  
wooden studs to screw the mounting  
brackets into.  
screws  
spacer  
mounting  
bracket  
16”  
3 Mark the wall at the center of the studs  
using the PenciL.  
4 Line the LeVeL up on both of your marks  
to make sure they are level. If they’re not,  
adjust the marks as needed to make them  
level.  
5 After you’ve double checked your markings,  
driLL through the top hole on both  
mounting brackets directly into the marks  
you’ve made on the wall.  
ITP280B  
6 If you are using the brackets only and no  
spacers, use the included short screws.  
If you are using any of the spacers or  
combination of the spacers, use the long  
screws.  
ITP280B  
7 Use the LeVeL to level each of the hanging  
brackets, then drill the second screw  
into the bottom hole on both mounting  
brackets.  
8 Slide the bar speaker onto the mounting  
brackets, and make sure there is a firm and  
stable connection before letting go of the  
bar speaker.  
9 Finally, use the LeVeL to confirm that the  
bar speaker is level.  
CUsTOmeR HeLPLINe | 1-314-621-2881  
iLive | ITP280B  
15  
 
coMPany inforMation  
green initiative  
environmental Commitment to ‘Protect for Today  
and sustain for Tomorrow’  
2009 marks the official launch of DPI, Inc.’s corporate  
campaign for a greener and cleaner world. DPI and  
its four brands, iLive, WeatherX, Capri, and GPX, are  
building upon environmental initiatives introduced  
at all of their facilities to help formulate and sustain  
significant and important conservation efforts within its  
manufacturing and marketing communities. In addition  
to targeting and selecting energy efficient product  
features, and structuring ‘green office’ procedures, other  
initial program efforts include:  
• Reduction of all packaging sizes  
• Recyclable plastics for clamshell packages, with a plan  
to eventually replace plastic with recyclable paper  
• Recycled fiber board in place of the polyfoam in  
packing boxes  
• Recycled plastics in place of the virgin material in  
product construction  
international support  
To download this User’s Guide in English, Spanish, or  
French, visit the support section at www.ilive.net.  
Para transferir esta guía de usuario en inglés, español, o  
Pour télécharger ce guide de l’utilisateur en anglais,  
espagnol, ou français, visitez la section de soutien chez  
contact information  
Address: 2116 Carr Street, St. Louis MO, 63106  
Phone: 1-314-621-2881  
Fax: 1-314-588-1805  
Parts Email: [email protected]  
and  
are trademarks of SRS Labs, Inc. TruSurround XT and WOW technologies are incorporated  
under license from SRS Labs, Inc.  
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are  
subject to change without notice  
 

Graco Food Saver 223646 User Manual
Grizzly Saw BT 160X User Manual
Hamilton Beach Slow Cooker 33245 User Manual
Hans Grohe Plumbing Product 06117000 User Manual
Hearth and Home Technologies Range be 36 c User Manual
Heat Glo LifeStyle Indoor Fireplace 6000 GDVFL User Manual
HP Hewlett Packard All in One Printer X20LED User Manual
HP Hewlett Packard Cell Phone 50091 1 002 User Manual
Huawei Cell Phone M835 User Manual
IKEA Indoor Furnishings AA 180830 1 User Manual